login   |    register

Scale Modeling Sponsors

See Your Ad Here!

New Content
Announcements on new content additions to the site.
Hosted by Todd Michalak
PHOTOS
PT 596
vonHengest
Visit this Community
Texas, United States
Joined: June 29, 2010
KitMaker: 5,854 posts
Model Shipwrights: 350 posts
Posted: Thursday, March 06, 2014 - 11:29 PM GMT+7
Michael Walsh shares with us his fully crewed Elco PT boat!

Link to Item

If you have comments or questions please post them here.

Thanks!
Gremlin56
Joined: October 30, 2005
KitMaker: 3,897 posts
Model Shipwrights: 3,301 posts
Posted: Friday, March 07, 2014 - 01:21 AM GMT+7
A very nice looking build,
Longshanks8
Visit this Community
England - South West, United Kingdom
Joined: July 04, 2013
KitMaker: 399 posts
Model Shipwrights: 367 posts
Posted: Friday, March 07, 2014 - 02:30 AM GMT+7
Shows the effort you have put in !

Cheers Kev
airborne1
Visit this Community
Queensland, Australia
Joined: April 15, 2006
KitMaker: 801 posts
Model Shipwrights: 33 posts
Posted: Friday, March 07, 2014 - 06:52 AM GMT+7
Thanks Guys, appreciate your kind words.

Michael
TAFFY3
Visit this Community
New York, United States
Joined: January 21, 2008
KitMaker: 2,289 posts
Model Shipwrights: 1,202 posts
Posted: Friday, March 07, 2014 - 11:51 AM GMT+7
Great job, the figures look real good.
Aurora-7
#360
Visit this Community
Connecticut, United States
Joined: June 18, 2003
KitMaker: 1,019 posts
Model Shipwrights: 630 posts
Posted: Friday, March 07, 2014 - 12:16 PM GMT+7
Great build. I'm forunate enough to live not too far from a fully restored PT-Boat (PT 617)
Grauwolf
#084
Visit this Community
Quebec, Canada
Joined: September 14, 2005
KitMaker: 2,031 posts
Model Shipwrights: 1,070 posts
Posted: Friday, March 07, 2014 - 01:27 PM GMT+7
Very nice build and figure painting.

I am still surprised to see that these boats did not have stanchions
with rope or rails, amidships and on the fore deck, to give the crew
something to hang on to, on tight turns and prevent them from flying
off the boat.

Cheers,
Joe
airborne1
Visit this Community
Queensland, Australia
Joined: April 15, 2006
KitMaker: 801 posts
Model Shipwrights: 33 posts
Posted: Saturday, March 08, 2014 - 03:54 AM GMT+7
Thanks Al ,Michael and Joe

dioman13
Visit this Community
Indiana, United States
Joined: August 19, 2007
KitMaker: 2,086 posts
Model Shipwrights: 195 posts
Posted: Saturday, March 08, 2014 - 05:13 PM GMT+7
Hey Michael, beautifull boat. I keep seeing two sets of cables for the torpedoes, thought it was one that looked like an inverted v going to the latch release, though I could be wrong as I am at times. Still looks fantastic in my eyes.
Hey Joe, stanchoins were usually removed to facillitate movement in combat areas. They were stashed in a locker unless they were in a port with brass around. The hold line runs in the center line and would interfer with the 20mm and or the auto cannon out of the aircobra when field moddified.
airborne1
Visit this Community
Queensland, Australia
Joined: April 15, 2006
KitMaker: 801 posts
Model Shipwrights: 33 posts
Posted: Saturday, March 08, 2014 - 09:09 PM GMT+7
Thanks Bob

The cables had been as per the kit instructions .I found the kit tie cables too thick to tie through the torpedoes so I ended up using copper wire .

Thanks for the info on the stanchoins

Michael
TGarthConnelly
Visit this Community
Connecticut, United States
Joined: August 03, 2008
KitMaker: 855 posts
Model Shipwrights: 852 posts
Posted: Sunday, March 09, 2014 - 08:42 AM GMT+7
Very nicely done, sir.
TAFFY3
Visit this Community
New York, United States
Joined: January 21, 2008
KitMaker: 2,289 posts
Model Shipwrights: 1,202 posts
Posted: Sunday, March 09, 2014 - 06:46 PM GMT+7
Bob, those cables were for added safety to prevent accidentally losing a fish overboard. They are like a vee, they run from two eyebolts on the back of each upright, around the torpedo, and disappear underneath. Not sure, but I believe they were released some time before launching the torp. Al
airborne1
Visit this Community
Queensland, Australia
Joined: April 15, 2006
KitMaker: 801 posts
Model Shipwrights: 33 posts
Posted: Monday, March 10, 2014 - 01:45 AM GMT+7
Thanks Garth,

Al, thanks for the info

Michael